10 Often-Ignored Issues Causing Oil Well Production Decline: Field Experience Guide

oil pipeline pump, screw pump application, Causes of oil well production drop

In oilfields, it’s common to see this: yesterday’s daily production was 8 tons, today it’s only 6 tons. The pumping unit is working normally. The motor is working normally. There are no alarms. The equipment hasn’t stopped. Yet, production keeps decreasing. Many people’s first reaction is: should the well be repaired? In fact, significant production reductions in many oil wells don’t happen suddenly; they are the result of the long-term accumulation of subtle changes.

Truly experienced oilfield engineers don’t wait until the well stops producing before analyzing it; they detect anomalies in various production parameters before production declines. There’s an old saying in the oilfield: “A well doesn’t suddenly break down; it just keeps reminding you.”

Many wells with reduced production have already given signals days or even months in advance. Today, based on field experience, we’ll share ten easily overlooked problems in oil production. These problems may seem insignificant, but they often determine the production of an oil well.

01. Abnormal Casing Pressure – Many Only Record, Don’t Analyze

Casing pressure is recorded almost daily. However, few people actually analyze it. Many field inspection personnel simply copy the data: Today: 0.25MPa; Tomorrow: 0.32MPa; Day after tomorrow: 0.48MPa; record ends.

In fact, changes in casing pressure are themselves important signals of well condition.

For example: A sustained increase in casing pressure may mean:

  • Gas accumulation;
  • Gas leakage in the casing;
  • Gas accumulation in the annulus;
  • Increased formation gas supply.

A sudden drop in casing pressure may indicate:

  • Casing leakage;
  • Annular venting;
  • Seal failure.

Case Study:

A certain pumping well had a stable daily production. Within a week, the casing pressure rose from 0.2MPa to 0.8MPa. No one paid attention. Half a month later, the well experienced severe gas lock, resulting in a 40% drop in production. Later, a gas anchor was installed, and normal production was restored. Experience: Casing pressure changes often precede production changes.

02 Oil Pressure Changes – Easiest Reflection of Downhole Fluid Supply

Many people record oil pressure daily, but rarely analyze trends. For example, decreasing oil pressure may indicate insufficient fluid supply or a reduced pump fill level. A continuously rising oil pressure may indicate excessive wellhead throttling, increased pipeline back pressure, or wellbore blockage. Therefore, higher or lower oil pressure is not always better. The key is whether it conforms to normal production patterns.

03 Decreasing Dynamic Fluid Level – Underground “Oil Shortage” Begins

Dynamic fluid level can be understood as the height of the fluid level in the well during production. The earliest change in many well production declines is a decrease in the fluid level. This indicates that the underground fluid supply rate cannot keep up with the pumping rate. If high pumping speeds continue, it can easily lead to: dry pumping, gas lock, rod string impact, and ultimately, increasingly lower pump efficiency.

Field Case:

A well’s daily production decreased. The pumping unit was operating normally. Tests revealed a 300-meter drop in dynamic fluid level. Subsequently, pumping frequency was reduced, and intermittent pumping was implemented. Daily production actually increased by 15%.

04. Wellhead Back Pressure Changes – Many Production Reductions are Related to This

In many older oilfields, the gathering and transportation network becomes increasingly complex. As valves, pipelines, and separators age, wellhead back pressure constantly changes. If back pressure increases, bottomhole flowing pressure rises, making it harder for crude oil to flow out. The ultimate result is a decrease in production, especially noticeable in low-pressure wells.

Field Case Study

After a combined station changed its process, over a dozen nearby wells experienced an average production reduction of 8%. It was later discovered that the gathering and transportation pressure had increased by 0.3 MPa. After reverting to the original process, production fully recovered.

05. Abnormal Dynamometer Diagram – The Well’s “Health Check Report”

The dynamometer diagram is often referred to as the well’s electrocardiogram. Many faults are undetectable by the equipment, but the dynamometer diagram provides early warning. For example:

• Pump leakage;

  • Air lock;
  • Insufficient fluid supply;
  • Valve leakage;
  • Rod breakage;
  • Pump jamming.

In many fields, dynamometer cards are only tested when a fault occurs. In fact, excellent oilfields conduct regular tests to detect problems early.

06. Poor Pumping Unit Balance – Not only does it increase power consumption, but it also easily leads to reduced production.

gas well boosting multiphase pump

Many pumping units, after replacing the pump diameter, stroke, and rod string, are not rebalanced. The result: the upstroke becomes increasingly heavy, and the downstroke becomes increasingly light. This manifests as: current fluctuations, increased power consumption, and increased stress on the rod string. Long-term operation easily leads to: rod breakage and pump wear, ultimately affecting production.

Field Case

A well had a long-term high current. It was thought to be due to motor aging. Later, it was discovered that the balance rate was less than 70%. After adjusting the balance weight, power consumption decreased, and pump efficiency improved.

07. Leakage – A Little Leak Every Day, Staggering Losses Over Six Months

The most easily overlooked issue on-site: “small leaks.” For example: minor oil leakage from packing, flange seepage, valve dripping. Many people think: no big deal. In reality: accumulated over a year, the loss could reach tens of tons of crude oil. More importantly, leakage also pollutes the environment, increases safety risks, and reduces system pressure.

On-site Case

A wellhead packing was dripping oil for a long time. Less than 2 liters per day. Accumulated over a year: more than 700 liters of crude oil. This not only caused economic losses but also resulted in an environmental inspection report for on-site pollution.

08. Early Stage of Wax Formation – Don’t Wait for Well Blockage to Deal with It

Many waxy oil wells initially only show: a slight decrease in production and slight changes in oil pressure. If left untreated, the wax layer will become increasingly thick, eventually completely blocking the tubing. Many wells on-site could actually avoid shutdown simply by: pre-treatment with hot flushing or adding chemicals.

09. Water Cut Changes – Not Just Look at the Levels, But Also the Trend

Many oilfield workers only focus on today’s water cut: 90%. However, what truly matters is the rate of change. For example, a monthly change from 80% to 88% to 92% to 92% to 95% indicates a water breakthrough or water channeling has occurred. Timely analysis allows for measures such as water shut-off, profile control, and injection-production adjustments. Continuing to delay will only result in less remaining oil.

Case Study

A well maintained a daily fluid production of 20 tons. Operators considered production stable. However, within three months, the water cut increased from 78% to 94%. Due to the failure to adjust the development plan in time, daily oil production dropped from 4.4 tons to 1.2 tons. Production only gradually recovered after profile control and water shut-off. Lesson learned: Unchanged daily fluid production does not necessarily mean normal production.

10. Long-Term Lack of Parameter Adjustment – ​​Many Oil Wells Operate Inefficiently

Many oil wells, from the start of production, have not undergone adjustments to parameters such as stroke, stroke frequency, pump diameter, or pump hanger. In reality, underground oil reservoirs are constantly changing. Production systems should be adjusted accordingly. Otherwise, either pumping too fast or too slow will result in declining pump efficiency.

Case Study

An old well maintained the same production parameters for three consecutive years. After re-analysis, technicians discovered that the fluid supply capacity had decreased. Adjusting the pumping frequency from 10 to 7 times improved pump efficiency from 58% to 82%, increasing daily oil production by 18%. Simultaneously, power consumption decreased significantly.

11. Why are many problems easily overlooked?

The reason is actually quite simple. Many field managers focus more on whether the equipment has stopped, rather than whether the equipment is operating at its optimal condition. Truly excellent oilfield engineers monitor daily:

  • Changes in production;
  • Changes in pressure;
  • Changes in fluid level;
  • Changes in current;
  • Changes in dynamometer card;
  • Changes in water cut.

Because these parameters often appear earlier than equipment alarms.

12. Field Inspection Recommendations:

Which indicators should be focused on daily? Based on years of field experience, it is recommended to include the following indicators as key points in daily inspections.

Inspection Items Key Focus Areas Potential Problems
Casing Pressure Is it continuously rising or falling? Gas lock, gas leakage, casing leaks
Oil Pressure Is it deviating from the normal range? Insufficient fluid supply, wellbore blockage, back pressure changes
Dynamic Fluid Level Is it continuously decreasing? Insufficient formation fluid supply, unreasonable pumping system
Dynamometer Diagram Is the graph abnormal? Pump leak, valve leak, gas lock, stuck pump
Current Is it fluctuating or rising? Poor balance, mechanical failure, changes in downhole load
Water Cut Is it rising rapidly? Water channeling, breakthrough of high water-cut formations
Back Pressure Is it increasing abnormally? Increased resistance in the gathering and transportation system
Leakage Is there any seepage or dripping? Crude oil loss, safety hazards
Pumping Unit Is there any abnormal noise, vibration, or uneven wear? Mechanical failure, poor alignment
Production Parameters Has it not been optimized for a long time? Decreased pump efficiency, increased energy consumption

13. In Conclusion

There’s a classic saying in the oilfield: “What truly causes well production to decrease is often not major malfunctions, but rather those small, long-overlooked problems. An oil well doesn’t suddenly reduce production without warning. Changes in casing pressure, a drop in dynamic fluid level, an increase in water cut, fluctuations in back pressure, anomalies in the dynamometer card… these seemingly insignificant data points are all ‘early warning signals’ from the well.

Excellent oilfield engineers not only know how to handle malfunctions, but more importantly, they can use dynamic analysis to detect problems early and nip production declines in the bud. Oilfield production management isn’t about the speed of well repair, but about who can detect anomalies earlier and take more precise measures. This is the core of refined development and stable production increases in older oilfields.”

Facebook
Twitter
LinkedIn
X
WhatsApp
Reddit

Contact Us for More Screw Pump Solutions

You might also enjoy

multiphase pump, shale gas pump

Tell Us Your Requirements

Ask Us Anything Anytime